4992 Main Street, Springfield, OR 97478
Phone: 541-746-2576  Fax: 541-746-2579
Hours: Monday-Friday  7:00am-5:00pm 
We accept Visa, MC, Discover & American Express
Square Deal Lumber
  • Home
    • Our Company
  • Products
    • Product Overview
    • New Arrivals!
    • Lumber Products >
      • Engineered Wood Products
      • Plywood
    • Siding
    • Insulation
    • Decking/Railing
    • Tools and Hardware
    • Paint and Stain
    • Doors
    • Plumbing accessories
  • Our Services
  • Specials
  • Contact Us
  • Employee gallery
  • DIY Blog

Creating a Frame Using Moulding

5/19/2014

1 Comment

 

Wallpaper Moulding Frame

Picture

Baseboard moulding can be made into a decorative frame for any wall in your house. You can either cut the corners at 45 degree angles, or use a corner block or other decorative square for the corners. Using a block in the corners eliminates the need for angle cuts on the trim. There are multiple ways to use the frame once you have completed it.

Supplies:

Stud finder

Tape measure

Pencil

Trim Pieces

Corner blocks, if desired

Level

Saw (circular/miter, etc.)

Nails

Nail Gun

Construction Adhesive

Wallpaper or paint for interior of frame

Instructions:

1. Determine where on the wall to place or mount the trim frame. A frame can be built under or over a chair rail. You can also put a frame on a bare spot on a wall or over a fireplace.

2. Decide how large you want the frame to be. You could measure the wall first and determine the size that way, or just pick a size and go for it! (Make sure the frame size is smaller than the wall size.)

3. Using the stud finder, find the location of the studs in the wall and mark with a pencil. If using nails, you will need to plan carefully to attach your blocks and trim to the studs. If you use adhesive, stud location is not as important.

4. Measure the width of the corner block with the tape measure. The width of the block may vary, but a typical size is 2 inches.

5. Measure and mark trim pieces for the frame with the tape measure and pencil. Example: A 2 foot wide by 3 foot high frame will require 4 pieces of trim. The 2 pieces used for the width will need to be 20" long and the 2 pieces for the height will need to be 32" long (remember-the corner blocks are about 2")

6. Cut the trim to the length needed with a circular or miter saw.

7. Set one of the corner blocks in place on the wall, level it, and secure it with a nail gun. If you do not want to use a nail gun, apply construction adhesive to the back of the block and adhere to the wall.

8. Place one of the width trim pieces flush to the corner block. Secure the trim to the wall using the nail gun or construction adhesive.

9. Set another corner block in place at the end of the trim. Add the next section of trim, measured for length, and secure it to the wall. Add the remaining corner blocks and trim pieces until you have completed the frame.

10. Cover the wall inside the frame with wallpaper (trimmed to size) or paint it a color that contrasts with your wall color to complete your project. You could placed framed pictures or other items inside of your moulding frame to create an unique wall piece.

Tips: Always wear protective eyewear when using power tools. Have rags handy to wipe up any spills.

Source reference: http://www.ehow.com_6719380_trim-wall-frame.html#ixzz32BKa17Yf







1 Comment

Build Your Own Planter Box

3/10/2014

3 Comments

 
Picture
Picture
Raised garden beds and planter boxes enhance the beauty and appeal of a deck, patio or entrance, adding color to it and encouraging different birds, bees and butterflies to frequent your space. Large planter boxes lined together, or placed in a few strategic spots outside your house, provide natural decoration and spruce up the surrounding landscape. You can create one in whatever size will fit your needs. These instructions are for a planter that is 36 inches long and 24 inches wide, with a height of 12 inches. Paint it to match the exterior of your house or in a complementary color. All materials are available at Square Deal Lumber.

Step 1

Purchase good quality wood (redwood or cedar) that is resistant to insects and wood rot. Cut it to size with a saw, or have a professional cut it for you. You will need five boards for your planter: two 12-by-36 inch pieces for the front and back, two 12-by-24 inch boards for the sides, and a base piece that is 36 inches long and 24 inches wide (exterior plywood will work).

Step 2

Drill several 1-inch drainage holes in the base piece, spaced equally apart.

Step 3

Lay the front piece on a flat and even surface. Place a side piece flush against it, making sure the joint is even and flush. Drill a 2-inch galvanized wood screw near the top edge of the side piece, which will penetrate through the side piece into the front board to join them together. Drill another wood screw near the lower edge, and any additional wood screws if you want a secure fit. You will have a structure that resembles an "L."

Step 4

Hold the back piece against the short side of the structure, aligning it to make sure the tops are at the same level and the joint is flush. Join it to the structure by drilling 2-inch galvanized woodscrews through the edge. Repeat the procedure with the second short side so it is attached to the structure and your large planter resembles a box that has no lid or base.

Step 5

Carefully lift the planter and turn it over so the lower side faces upward. You may need someone to help you turn it. Lower the base piece over the box and secure it by drilling several 2-inch galvanized wood screws into each edge. Turn it over and review your planter box.

Step 6

Sand the edges, corners and crevices to remove any splinters and give it a smooth finish. Apply colored or clear acrylic paint to the planter so it will last longer.  

Tips and Warnings

  • Always wear safety glasses and earplug when using a drill to prevent injury.

Things You'll Need

  • Five redwood or cedar boards, plus a 36" x 24" piece of plywood for base 

  • Gloves

  • Measuring tape

  • Circular saw

  • Protective eyeglasses

  • Earplugs

  • Drill

  • 2-inch galvanized wood screws

  • Sandpaper

  • Paint

References

  • Gardenguides.com

3 Comments

EASY PALLET SHELVES

1/31/2014

3 Comments

 
Picture
picture from http://www.pinterest.com/pin/231442868321441911/

DIY EASY PALLET SHELVES

These easy-to-create shelves would be great on a patio, in a kitchen, or in a garden area. You can sand the whole pallet for a more polished look, but I think leaving it as-is, then staining, fits the rustic look that these shelves provide.

Materials:

1 pallet

Wood stain of your choice

Brush for applying stain

Clean cloth


Clear Lacquer (optional)

Hammer


Sandpaper

Directions:


Place pallet on the ground and remove your chosen boards.

Sand around the nail holes if there are any splinters .

Hammer in any nails that are sticking out.

Apply stain according to manufacturer's instructions, using the brush and cloth.

Let dry.

Optional: You may want to coat the pallet with clear lacquer for a sealed finish. This will help protect the wall from any color transfer.

**Square Deal has all of your material needs for this project.**

3 Comments

EASY DIY STYLING or BBQ TOOL HOLDER

1/7/2014

3 Comments

 
Picture
This is a quick and simple way to create a hairdryer/hairstyling tool to eliminate some clutter from your bathroom counter. This could be a personalized, but inexpensive gift. Or, on the flipside, you could gift it to the BBQ enthusiast in your life to hold the BBQ tools. Great for a man or a woman.

Materials:

1-3" PVC "Y" or "W" connector ($7.29 at Square Deal)
1 can of spray paint (we have discount cans for $1.00 each)
Newspapers or tarp to protect painting area

Optional:
Glitter, stickers, additional decorations

Directions:

Clean connector with soap and water.
Dry completely, inside and out.
Place connector on newspapers.
Paint exterior of connector. Let dry completely.
Paint interior if desired.
Decorate exterior with glitter, stickers or additional paint. L
et dry.

***Be sure to cool your products before placing in the holder to avoid melting the paint and PVC.***

Enjoy!





3 Comments

DIY Christmas Tree or Holiday Decoration

12/3/2013

2 Comments

 
Picture
With a little time and effort you can create a rustic homemade Christmas tree that you can use for years to come. Great project for a small area or to just try something fun and new!

DIY Christmas Tree 

Materials needed:

2-8’ boards (1 x 6)

1-10’ board (1 x 6)
Green spray paint.
Brown spray paint (if desired).
Saw
Sandpaper to soften cut edges
Screws (1”)
Screwdriver
String of lights
Star for top (purchased or created)
Hanger for tree (can be purchased at Square Deal)

STEP 1: Make sure you have the space to hang your tree on a wall (approximately 4’ wide at base, approx 7’ high).

STEP 2: Visit SQUARE DEAL and purchase your lumber. You can get all the lumber you need from an 8’ board and a 10’ board for the horizontal slats. For the vertical “trunk” of the tree, an 8’ board will work and you can trim down to your desired height.  
 
STEP 3: Cut your boards to desired length, tapering down in size. 
1 board @ 48”
1 board @ 42”
1 board @ 36”
1 board @ 30”
1 board @ 24”
1 board @ 18”
1 board @ 12”
Using sandpaper, soften any rough edges. Don’t sand too much, this is a rustic tree! 
 

STEP 4: Paint all horizontal boards (branches) green. Paint vertical board (trunk) brown, if desired. Let dry.

STEP 5: Lay the “trunk” on a flat surface. Measuring from the top, mark at 4”, 14”, 24”, 34”, 44”, 54”, and 64”. These marks will be where you line up your “branches". 

STEP 6: Place your 12” board under the 4” mark, screw in place*
Place your 18” board under the 14” mark, screw in place*
Place your 24” board under the 24” mark, screw in place*
Place your 30” board under the 34” mark, screw in place*
Place your 36” board under the 44” mark, screw in place*
Place your 42” board under the 54” mark, screw in place*
Place your 48” board under the 64” mark, screw in place*
(These do no need to be perfectly centered, but if you want them centered, measure to the center of each board and mark. Use that mark as a guide to center the boards on the "trunk".)

*You may want to pre-drill the holes to prevent splitting. Use 2 screws per board.*

STEP 7:  Carefully flip your tree over and attach the picture hanging apparatus to the top of the trunk.

STEP 8: Hang your tree on the wall.

STEP 9: Arrange a string of lights around your tree branches.

STEP 10: Attach your star to the top. 

Enjoy your new tree!

  

2 Comments

DIY Wine Rack (great Christmas gift)

11/26/2013

0 Comments

 
This wine rack would be a great gift for Christmas or a birthday, especially if you include a bottle of wine! If you purchase a 1"X4"X10' board you could make 8 of these for gifts. A clear cedar board in that size will run you less than $8.00 at Square Deal.

Easy DIY Wine Rack

Picture
Materials needed: 
1" x 4" board cut to 15"
Measuring Tape
Pencil
Straightedge or ruler      
Miter saw       
Drill with 1-1/2-inch hole saw or Forstner bit
Sandpaper (medium and fine-grain)
Paintbrush
Paint or stain

INSTRUCTIONS:

PictureSTEP 1
1. To mark the correct angle for the base, measure 14-1/8 inches from one end. Using the straightedge and pencil, draw a horizontal line across the face of the board. Flip the wood over and draw another horizontal line 13-3/4 inches from the end. Then turn the project on its side and using the straightedge, connect the two horizontal lines.


PictureSTEP 2
2. Use a power miter saw (chop saw) to cut the marked angle as shown. This angle must be exact in order for the wine bottle to balance.

PictureSTEP 3
3. Opposite the angled edge, draw a small horizontal line in the center of the wood 3-1/8 inches from the top. Then mark a small vertical line 1-3/4 inches from either side of the board to create a crosshair.


PictureSTEP 4
4. Use the drill and 1-1/2-inch bit to carve a hole, aligning the bit with the crosshair. To avoid damage to your work station or the piece, you may want to clamp a piece of scrap wood under the project for this step.


PictureSTEP 5
5. Use the medium-grain sandpaper to smooth around the hole and  other rough edges. Then go over the piece with the fine-grain sandpaper. After sanding, paint, stain, or oil the stand as you please. Once it is dry, try it out!

0 Comments

    Author

    Nickie Rodriguez manages the FB page and website, as well as working part time at Square Deal. She is also the wife of General Manager, Tony Rodriguez.

    Archives

    May 2014
    March 2014
    January 2014
    December 2013
    November 2013

    Categories

    All
    Container Gardening
    DIY
    Garden Beds
    Moulding Projects
    Raised Garden Beds
    Wall Decoration

    RSS Feed

4992 Main Street, Springfield, OR 97478  Phone: 541-746-2576 Fax: 541-746-2579